ROUND Pools Ambassador Manuel d'utilisateur télécharger pdf (Page 25)

We manufacture two different kinds of wall joint assemblies. One has a single row of bolts with pre-attached aluminum wall

bars, and the other is a staggered double row pattern where the aluminum wall bars are not pre-attached. Please check which

design your pool has and follow the appropriate instructions below.

STEP 14: WALL JOINT ASSEMBLY

Type #1 Single Row

Pre-Attached

inside wall bar

Nut goes to

outside of pool

Pre-Attached

outside wall bar

Outside of pool

Inside of pool

Side wall

Inside wall bar

Outside of pool

Nut goes to

outside of

pool

Outside wall bar

Side Wall

Inside of pool

1/4” Nuts

Outside of pool

Inside of pool

3/4” Bolts

Wall bar

Pool wall

Wall bar

Pool wall

Top View

STAGGERED BOLT WALL BAR SYSTEM

REMEMBER:

ALL NUTS SHOULD BE AS TIGHT AS POSSIBLE USING HAND TOOLS. BARS MUST NOT TOUCH EACH OTHER. EVERY HOLE FROM TOP TO BOTTOM OF THE

WALL/WALL BAR SYSTEM MUST HAVE A SECURELY TIGHTENED NUT AND BOLT. IF THIS IS DONE INCORRECTLY YOUR POOL WILL BREAK!

IMPORTANT – This operation must be done carefully! When joining the side-

wall, make sure that the pre-attached aluminum strips do not touch each other.

One bar must be inside the pool (the bolts will touch this bar) and one bar must be

outside the pool (the nuts will touch this bar). Insert the bolts with the bolt head

to the inside and the nuts to the outside of the pool. Do not tighten until all bolts

have been inserted. If your screwdriver slips and scratches the head of the bolt,

file the scratch smooth so that it cannot puncture the liner. It is recommended that

you cover the heads of the bolts, on the inside of the wall, with three layers of duct

tape. If the insertion of the wall in the bottom rail is tight at the point where the wall

is joined together, insert a screwdriver and twist to make enough room, again being

sure not to scratch the wall or the bottom rail.

IMPORTANT – This operation must be done carefully! When joining the sidewall, make sure that the aluminum strips do not touch

each other. One bar must be inside the pool (the bolts will touch this bar) and one bar must be outside the pool (the nuts will touch this bar).

Insert the bolts with the bolt head to the inside and the nuts to the outside of the pool. Do not tighten until all bolts have been inserted.

If your screwdriver slips and scratches the head of the bolt, file the scratch smooth so that it cannot puncture the liner. It is recommend-

ed that you cover the heads of the bolts, on the inside of the wall, with three layers of duct tape. If the insertion of the wall in the bottom

rail is tight at the point where the wall is joined together, insert a screwdriver and twist to make enough room, again being sure not to

scratch the wall or the bottom rail.

Type #2 Staggered Bolt Pattern

• If you are missing any hardware, do not leave

empty holes in the wall joint assembly. Doing so will

cause your pool to break! See your pool dealer for

additional hardware in the case of a shortage.

REMEMBER:

ALL NUTS SHOULD BE AS TIGHT AS POSSIBLE USING HAND TOOLS. BARS MUST NOT TOUCH EACH OTHER. EVERY HOLE FROM TOP TO BOTTOM OF THE

WALL/WALL BAR SYSTEM MUST HAVE A SECURELY TIGHTENED NUT AND BOLT. IF THIS IS DONE INCORRECTLY YOUR POOL WILL BREAK!

• If you are missing any hardware, do not leave empty holes in the wall joint assembly. Doing so will cause your pool to break!

See your pool dealer for additional hardware in the case of a shortage.

Every hole from top to bottom of wall/Wall bar system must have a securely tightened nut and bolt.

*Wall bars must not

touch each other

Fig. 47

*Wall bars must not

touch each other

Fig. 48

Fig. 49

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

ROUND Pools Ambassador Manuel d'utilisateur Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Piscines hors sol ROUND Pools Ambassador